MicroBoards Technology Copywriter Flash Duplicator Manual do Utilizador Página 10
- Página / 15
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Microboards Technology, LLC
10
6. Setup
ENT
1. Language
3. Write Error Skip
4. Size Tolerance
5. Buzzer
6. Screen Saver
This setting can be changed to
alter the Write Error behavior.
A
llows you to change tolerance of
different size master and blank flash
drives.
Turns the buzzer ON or OFF.
This setting specifies the language
displayed on the interface.
▼
▼
▼
▼
ENT
ENT
ENT
ENT
ENT
This setting can be changed to
alter the Read Error behavior.
2. Read Error Skip
▼
ENT
Turns the Screensaver ON or
OFF.
Setup
The Setup menu gives you access
to some of the default settings used
by the Copywriter Flash Duplicator.
Language
This setting specifies the language on the display.
The default language is English.
Read Error Skip
This setting will allow you to change the number of
times you want the system to skip ahead when the
system encounters a reading error while reading
your original Flash Storage Device. By default, the
system does not skip any reading error. Under this
setting, if the system encounters any errors, it would
result in an immediate job failure.
This function will not fix any discovered error. It will
merely skip the error and copy the remaining data.
The setting will allow the number of errors specified
before generating an error.
Write Error Skip
This setting will allow you to change the number of times the system will skip when the system
encounters a writing error during the copying process. By default, the system does not skip any
writing errors. Any writing errors would result in an immediate failure on this Flash Storage
Device.
This function will not fix any errors that it may find. It will only skip errors to write the remaining
data. The setting will allow the number of errors specified before generating an error.
Size Tolerance
This setting allows you to determine how closely the capacity of the target cards match the
capacity of the source card. The Size Tolerance behavior will change depending on the Copy
Mode setting (see page 9). If Copy Mode is set to Smart Copy, the size of the data on the
source will be checked against the target drive capacity. If Copy Mode is set to RAW Copy, the
target drives must be as large as or larger than the source regardless of the data size being
copied.
Options are: OFF (target cards must be the same capacity or larger than the source card), 1%
difference in capacity size between the master and the blanks, 5% difference, or IGNORE.
Because errors can occur if the Size Tolerance is set to IGNORE, we do not recommend the
IGNORE setting, but is available if you absolutely need it.
This setting is intended for flexibility if the source card is a low-capacity card. Note that even if
the target drives are larger than the source drive, this setting can generate a false error state.
Any attempt to duplicate more data than the target card’s capacity will fail.
Buzzer
This setting allows you to turn ON or OFF the beep produced when the buttons are pressed or
an audible status cue is provided. The default setting is ON.
Screen Saver
This setting turns the screensaver ON or OFF. Default setting is ON.
- Copywriter 1
- Flash Duplicator 1
- Microboards Technology, LLC 2
- Table of Contents 3
- Introduction 5
- Installation 5
- Hardware Description 6
- Main Menu Flowchart 7
- Main Menu 8
- Copy & Compare 9
- Copy Mode 9
- Utilities 11
- Manage Accounts 12
- Shutdown 12
- Asked Questions 13
- Specifications 14
- Contact Information 14
- Appendix 2: LED Indicators 15
Manuais e produtos relacionados com Duplicadores digitais MicroBoards Technology Copywriter Flash Duplicator
(18 páginas)Sencor SVC 510GR manuály
Uživatelské manuály a uživatelské příručky pro Vysavače Sencor SVC 510GR.
Poskytujeme 1 manuály pdf Sencor SVC 510GR ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais